What should you do to lift a pallet and raise the forks on the truck?

Check that the overhead clearance is adequate before raising loads. Do not raise or lower the fork unless the lift truck is stopped and braked. Lift loads straight up or tilt back slightly. Do not lift a load that extends above the load backrest unless no part of the load can possibly slide back toward the operator.

What should you do before raising the forks or platform on your lift truck?

Requirements and Recommended Practices:

  • Approach the load slowly and carefully. …
  • Do not raise or lower the forks unless the forklift is stopped and the brake is set.
  • Prior to raising the load, ensure there is adequate overhead clearance. …
  • Use the inching pedal to creep the load to the stack.

How do you move the forks on a forklift?

Raise the fork slightly. The fork will be resting in a small groove in the crossbar; nudge the fork out of the notch so that it will slide along the top of the crossbar. If the forks are rarely adjusted they may be very hard to move. If so, move to the end of the fork and move it from side to side to break it free.

IT IS INTERESTING:  What can I substitute for hydraulic jack oil?

How do you lift a load with a forklift?

Lift the load and tilt it back a little more before traveling. Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back.

A forklift platform must comply with HSE PM28 regulations in addition to being fully compatible with the forklift truck. … It is essential that the total load weight does not exceed more than half the total load capacity of the forklift truck. A forklift truck cage must be secured to the truck itself or the forks.

How much back tilt should be applied when picking up a load?

Carry the load at the lowest position possible, 4 to 6 inches from the ground. Tilt the mast back and position the heaviest part of the load against the carriage.

What do you lift pallets with?

Hand operated and electric pallet handling equipment, also known as Pallet Trucks, are the easiest and quickest method of moving pallets. Capable of holding and lifting up to 5000kg, a pallet truck is suitable for almost every moving operation; which is why you will find them in most warehouses.

What would you use to move pallets?

A pallet jack, also known as a pallet truck, pallet pump, pump truck, scooter, dog, or jigger is a tool used to lift and move pallets. Pallet jacks are the most basic form of a forklift and are intended to move pallets within a warehouse.

What should you check before lifting a load?

Check that the overhead clearance is adequate before raising loads. Do not raise or lower the fork unless the lift truck is stopped and braked. Lift loads straight up or tilt back slightly. Do not lift a load that extends above the load backrest unless no part of the load can possibly slide back toward the operator.

IT IS INTERESTING:  What does it mean to hoist the sails?

Which steps should you do every time you park a forklift?

  1. Select an area to park. Do not park in an unauthorized area. Do not block an aisle or exits. Follow your company’s parking procedures.
  2. Apply brake slowly and stop.
  3. Neutralize the controls.
  4. Set the parking brake.
  5. Turn off the ignition.
  6. If the truck is parked on an incline, block the wheels.

When traveling with empty forklift the forks should be in what position?

Adopt a stable position and make sure your feet are apart, with one leg slightly forward to maintain balance.

What position do you place the forks when parking your forklift?

To achieve a safe “parked” fork position, an operator lowers the forks completely with the mast vertical. The mast is then tilted slightly forward until the fork tips touch the floor, preventing a pedestrian’s hook fall.

What is the biggest danger when driving a forklift on a dock?

Wet or Icy Surfaces

Even though they’re moving at slower speeds than conventional vehicles, forklifts can still skid on wet, icy, or oily dock surfaces or dock levelers. A slippery dock area can also cause moveable dockboards to shift out of place, which can be dangerous when heavy lift trucks are driving over them.

When picking up a load the forks should be?

The forks should be at least two-thirds the length of the load. The mast must be carefully tilted backward to stabilize the load. Ensure the load is secured before moving. Slowly move the truck to 20 to 30 cm (8 to 12 inches) away from the stack.

IT IS INTERESTING:  What are the classes of forklifts?

What class lift trucks should not turn on an incline?

MAKE SURE YOUR FORKS ARE JUST HIGH ENOUGH TO CLEAR THE TRAVEL SURFACE. PEDESTRIANS AND FORKLIFTS SHOULD NEVER OCCUPY A RAMP OR INCLINE AT THE SAME TIME, IF THE OPERATOR OF A CLASS 1, 4, & 5 IS CARRYING A LOAD THAT BLOCKS THEIR FORWARD VISION ON LEVEL SURFACES, THEY ARE TAUGHT TO DRIVE IN REVERSE.

Vira!