The safe traveling distance between forklifts is approximately three truck lengths, or about a time-lapse of three seconds when passing the same point. More specifically, it’s about 20 feet between forklifts. The three-second rule is the same for automobiles on the road and is just as important for forklifts.
What is the minimum safe distance to drive behind another forklift?
Falling distance of an object from a pallet or 15 feet, 5 Feet both sides, 5 Feet Rear of Forklift. do so (ALL CLEAR). Do not pass under the forks while in operation.
How many feet does it take for a forklift to stop?
The driver will usually travel about 7 feet before he or she has time to apply the brakes (and that’s assuming that the driver is paying close attention to his surroundings, which is not usually the case). It will take another 10 feet for the forklift to come to a full-stop.
What distance is the exclusion zone around a forklift?
Designate exclusion zones for pedestrians and forklifts. Pedestrian exclusion zones should be enforced within a three metre radius of a forklift. This distance should expand when the height of the forklift load or the speed travelled increases.
How many pallet lengths should you leave for a safe stopping distance?
Protect yourself and the other workers around in the workplace, always follow the traffic rule and always maintain the good safe practices when doing forklift operation. Keep in mind that a safe distance between forklifts traveling in the same direction is approximately three truck-lengths.
When traveling with a load the load should be lifted How many inches?
Carefully lift the load up above the lower stack about 10 cm (4 inches). (Figure 9) Lift the load clear and then tilt the mast back slightly to rest the load against the load backrest extension. Ensure that the load does not catch on any obstructions.
When traveling with empty forklift the forks should be in what position?
When travelling in an empty forklift, the forks of the lift should be in the position of waist high.
Why are forklifts so dangerous?
There are many factors that explain why forklifts are dangerous: … The load of a forklift is carried in the front of the vehicle, blocking the line of sight of the operator. Forklifts are frequently required to lift heavy loads to high places. Mistakes made during lifting can lead to serious injuries from falling loads.
Who has the right of way in most warehouses?
OSHA states the pedestrian has the right of way; therefore, operators must be on constant alert. The forklift operator is required to slow down and sound their horn at doorways, intersections, blind spots and when entering or exiting a building.
Which side of the forklift is supporting more weight?
The forklift is more stable when it is properly loaded than when it is unloaded. However, improper loading, such as loading the forklift beyond its capacity, or loading an oversize or wide load without adjusting the weight, will cause the forklift to tipover, either laterally on its side or longitudinally forward.
Can a fully loaded forklift use its brakes to the maximum?
A laden forklift cannot use its maximum braking capacity, because the load may slide or fall from the fork arms, or the forklift will tip forwards. SPRAINS AND STRAINS Sprains, strains and other soft tissue injuries to the neck, back and arms can cause long-term health problems.
Do forklifts have the right of way?
Operators should yield the right of way to pedestrians: This is an OSHA recommendation that all forklift drivers should be aware of. Because of the size and power of the forklift, operators should stop and wait for pedestrians to clear the area before proceeding along their route with caution.
How do I control my forklift speed?
Install forklift speed bumps. These help control speed by forcing trucks to come to a complete stop to pass over them. Place them in crosswalks, pathways, blind spots and areas with pedestrian traffic. Install speed limiting devices on your forklifts.
What will make the load more stable during travel?
When traveling with a load, always make sure to tilt the mast of the forklift backward so that the load will firmly place against the backrest to make it more secure during transport. By doing this, you move the center of gravity towards to rear of the forklift making it more secure when traveling.
How long does it take to stop a forklift that is traveling at full speed?
A forklift travelling at 6km/per hour usually requires around 3 meters to come to a safe stop.
What should not be done when operating a forklift?
- Do not lift or move a load unless both forks are fully under the load.
- Do not lift a load with one fork. Use pallets and skids that can withstand the weight of the load.
- Do not use damaged, deformed or decayed pallets for holding loads.