If you want to install a typical 2-post or 4-post lift in your garage, you need a ceiling that’s higher than 11 feet.
How much height do you need for a 2 post lift?
Typically, a 12-foot minimum clearance, floor to ceiling, is required for your general two-post lift. Higher ceiling height is required for some of the four-post storage lifts and anything designed for larger trucks.
How thick of concrete do you need for a 2 post lift?
Some of manufacturers standards for a 2-Post and 4-Post Lifts require a minimum 4 inches of reinforced concrete slab to be safely installed.
How tall does your garage need to be for a lift?
A car lift will optimize any space, so don’t fret if you’re concerned that your garage is too small. The car lift itself will fit into one bay space and it is optimal to have 11-12 feet clearance height. Garage Living also has modified garage doors to accommodate the lift.
What size anchors for 2 post lift?
What size concrete anchor bolts are needed? Most 2-post lifts comes with enough ¾” x 5 ½” concrete anchor bolts for the initial installation of your lift.
Are 2 post lifts safe?
Two-post car lifts are some of the most popular lifts in the world. They’re safe and reliable when used correctly, and they have high lift capacities. At BendPak, we make two-post lifts that hold up to 18,000 lbs. … These facts remain true for every car lift of every brand, by the way.
Which is better 2 post or 4 post lift?
A four post lift takes up much more room than a two post lift. A two post lift will raise a car “higher” in a low ceiling garage. This is because the four wheel assemblies hang below the four lifting arms (the vehicle is lifted by the frame). … A four post lift makes it much easier to load and position the vehicle.
Where should a 2 post lift be installed?
If your lift has asymmetric arms, then we recommend the center of the columns should be set about 9-10 feet off the front wall. If your lift has symmetric arms, then we recommend that the center of your columns should be about 12 feet off the front wall.
How thick of a floor for a lift?
Pre-Existing Minimum Floor Requirements:
|TWO‐POST MODELS||MIN. THICKNESS||REBAR SPACING|
|XPR‐12 SERIES MODELS||6 1/2″||10 in|
|XPR‐15 SERIES MODELS||8″||10 in|
|XPR‐18 SERIES MODELS||8″||10 in|
|4‐POST LIFTS||MIN. THICKNESS||REBAR SPACING|
How thick does a concrete slab need to be for a shop?
If these steps are performed correctly, the owner can expect an attractive, durable product. Standard concrete floor slab thickness in residential construction is 4 inches. Five to six inches is recommended if the concrete will receive occasional heavy loads, such as motor homes or garbage trucks.
How much does it cost to install a garage lift?
BendPak says the typical cost for having a professional install a garage car lift is $500 to $10,000, depending on type. The installation process itself will depend on what kind of home garage lift you get (portable lifts notwithstanding).
How much room do you need for a 4 post lift?
Your garage needs enough space before you can install an auto lift. The typical measurements for a 4-post car lift is 103 inches wide by 173 inches long. Most passenger cars have a length of approximately 16 to 17 feet. If the cars you work on fall in this range, then this type of lift may be right for you.
How much is a car lift for a garage?
A standard two-post car lift with a capacity of around 10,000 pounds will usually run anywhere between $2,000 and $3,500, which is about the same price as a lower capacity four-post auto lift.
Can a 2 post lift be installed outside?
Technically, the correct answer is, “You can put it outside (as in, who’s stopping you?), but should you?” Lifts are designed for indoor use, installed in a temperature-controlled environment.
Do you have to bolt down a 4 post lift?
Do 4-Post Lifts Need to be Bolted Down? … Unlike 2-post lifts, which absolutely need to be bolted down, 4-post lifts disperse weight across a wider surface area and are engineered to lift vehicles with or without drop-in anchor bolts .