The United States Department of Labor states that the best way to get into or out of a forklift is through careful movement and being slow.
How do you drive a forklift step by step?
Put the forklift in neutral, set the parking brake, and inspect the load to make sure it is centered over the forks and balanced. Lift the load by pulling the leftmost lever toward you. Keep the load low to the ground to keep the forklift’s center of gravity low. Drive in reverse if the load blocks your view.
How should you normally drive your forklift?
Always operate the forklift at a speed that will allow you to stop it in a safe manner. Slow down when driving on wet or slippery floors. If the load you’re carrying obstructs your forward view, travel with the load trailing instead.
What are the 3 pedals on a forklift for?
To begin with, every forklift comes equipped with an accelerator and a brake pedal. That third pedal is called an Inching Brake. Its function is twofold. It initially acts as a brake and secondly disengages the transmission, allowing the engine speed to increase or decrease without affecting the drive of the forklift.
Do forklift drivers have the right of way?
Operators should yield the right of way to pedestrians: This is an OSHA recommendation that all forklift drivers should be aware of. Because of the size and power of the forklift, operators should stop and wait for pedestrians to clear the area before proceeding along their route with caution.
Can you fail a forklift test?
Forklift operator practical test penalties
There is for the written test but not for the practical. In fact it’s very simple. … After the test they get added up by the instructor and the total must not exceed 40. If a trainee scores 41 or more they are deemed to have failed the test.
Is forklift driving hard?
It’s not really that hard; it’ll be weird at first learning to drive forward and backward, and each machine can be quite different (traditional forklifts, hi-lo forklifts, order pickers, gas, electric, etc.). Just avoid getting complacent and resist the temptation to do anything stupid.
How high should your forks be when driving forklift?
Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back.
What can you not do with a forklift?
Forklift safety: things your drivers should never do
- Raise or lower loads while the forklift is moving and especially not while turning because it makes the forklift very unstable. …
- Allow anyone to stand underneath or right next to raised forks. …
- Carry a load with only one fork as it stresses the carriage.
Why is carrying a load on one fork dangerous?
With forklifts, the center of gravity is low to the ground, as this is where most of the truck’s own weight is. But when it is carrying a heavy load, and lifts it several meters high, things change. This can be especially dangerous when cornering at speed.
How long does a forklift last?
The average lifespan of a forklift is 10,000 hours, but this depends on the manufacturer. Above-average machines, such as Toyota forklifts, commonly last more than 20,000 hours.
What is a inching control on a forklift?
The purpose of the inching pedal is to disengage the transmission without having to shift the gear lever into neutral every time a lift is performed. This pedal allows you to bring the forklift to a stop or to slow it down. … This pedal allows you to adjust the rotational speed of the engine.
What is a safe speed for a forklift?
The Material Handling Equipment Distributors Association (MHEDA) recommends a max speed of 8 mph in general and a 3 mph max speed in areas where pedestrians are present.
What is the most common forklift accident?
A forklift overturning is the most common incident, accounting for 24% of all forklift accidents. If companies implemented more stringent training policies, the Occupational Safety & Health Administration (OSHA) estimates that about 70% of forklift accidents in the US could be prevented.
Who has the right away on a forklift?
OSHA states the pedestrian has the right of way; therefore, operators must be on constant alert. The forklift operator is required to slow down and sound their horn at doorways, intersections, blind spots and when entering or exiting a building.
Which side of the forklift is supporting more weight?
The forklift is more stable when it is properly loaded than when it is unloaded. However, improper loading, such as loading the forklift beyond its capacity, or loading an oversize or wide load without adjusting the weight, will cause the forklift to tipover, either laterally on its side or longitudinally forward.