How does a 3 stage forklift mast work?

3-Stage – A three stage mast, or triplex, is the most versatile forklift mast and also the most popular. The outer rails allow for free lift, and the two inner sections can lift loads higher than a two stage.

How does a forklift mast work?

As you may already know, a forklift uses hydraulic pressure to raise the mast up by raising the lift cylinders. This, in turn, raises the inner mast channels, but without the lift chains, your forks and carriage aren’t going anywhere. And if your forks aren’t being lifted, you aren’t going to be getting much work done.

How high does a 3 stage forklift go?

Three Stage Mast

This will raise the forks and carriage near the top of the mast prior to the sections staging up (known as ‘Free Lift’). Typical lift height for a triple stage mast for a forklift with base capacity from 2,000 lbs. to 6,000 lbs. will have 189″ of maximum lift and will be around 83-88″ OAHL.

What is a forklift mast?

When selecting what forklift to purchase, the mast is one of the most important considerations. The forklift’s mast, or upright, is the portion of the forklift that lifts, lowers, and positions the loads manipulated by the forks.

IT IS INTERESTING:  Can you lay a bottle jack on its side?

How high can a forklift go?

Another measurement to consider is height. Most standard forklifts can reach heights between 10 and 15 ft, but special forklifts like the telehandler can lift as high as 55 ft depending on the telehandler size you select.

How much does a forklift cost?

A brand new, electric forklift with standard capacity might cost $20,000 – $45,000 dollars and up with an increase of $2,500 – $5,000 for a battery and charger. An internal combustion forklift with standard capacity will cost approximately $20,000 – $50,000 and up.

What is free lift on a forklift?

One metric that is often overlooked is forklift free lift. A forklift’s free lift is the maximum height you can raise the forks without changing the mast height.

How high is a 2 stage forklift?

Single-Stage Mast – Typically used in applications where overhead clearance is not a concern, such as outdoor environments. 2-Stage Mast – A 2-stage mast provides free lift and, when needed, the inner channel can extend for greater lift heights (generally 157 inches/13 feet).

When traveling load load should I lift?

Lower the load so that its lowest point is 15 to 20 cm (6 to 8 inches) from the floor. While traveling, keep the load at a safe travel height.

What are the three major parts of a forklift?

The three major parts of a lift truck are the body (truck), overhead guard, and hydraulic lift. You can place your hands and feet outside of the operator’s compartment, as long as your head and body are protected.

What are the best brands of forklifts?

Best Forklift Brands – Top 10 Manufacturer Comparison

  • >> See Yale Forklift Pricing & Details. #2 Hyster. Hyster might just be one of the most popular forklift manufacturers around. …
  • >> See Hyster Forklift Pricing & Details. ADVERTISEMENT. #3 Bendi. …
  • >> See Bendi Forklift Pricing & Details. #4 Drexel. …
  • >> See Drexel Forklift Pricing & Details. #5 Combilift.
IT IS INTERESTING:  How much does a stand up forklift cost?

29 сент. 2020 г.

How heavy is a forklift?

While the average automobile weighs around 3,000 pounds, the average forklift weighs around 9,000 pounds. Also, forklifts are heavier in the rear to counter the weight of items being carried in the forks.

How often should you grease a forklift?

All manufacturers recommend a weekly greasing schedule that must be followed to reduce downtime and costly repairs. For the purpose of going over grease points, we have selected a 16,000 lb forklift which will have similar grease point locations to most other models.

How often should a forklift be serviced?

The more you use your forklift, the more often you should have it serviced by a factory trained technician. A forklift that gets heavy use might require a forklift maintenance visit every 90 days. Be sure to keep a copy of the items inspected on file in case OSHA requests that information.

How do you lubricate a forklift chain?

Replace entire chain if any links are broken or cracked. Install the chains; then use a 1″ paint brush and lubricate both sides of chains with SAE-20 engine oil. Wipe off excess oil with a clean cloth. Adjust chains so fork carriage is level and all slack is removed from the lift chains.

Vira!