What must be clearly displayed on any overhead crane?

The rated load of the crane shall be plainly marked on each side of the crane, and if the crane has more than one hoisting unit, each hoist shall have its rated load marked on it or its load block and this marking shall be clearly legible from the ground or floor. Clearance from obstruction.

How do you inspect an overhead crane?

Items to be inspected:

  1. Deformed, cracked or corroded members.
  2. Loose bolts or rivets.
  3. Cracked or worn sheaves and drums.
  4. Worn, cracked or distorted parts, such as pins, bearings, shafts, gears, rollers, locking and clamping devices.
  5. Excessive wear on brake-system parts, linings, pawls and ratchets.

1 дек. 2018 г.

How do you maintain an overhead crane?

Ensure there are no loose, broken, or damaged parts on the hoist, trolley, bridge, runway, or electric systems. Check that the wire rope is reeved and seated in the drum grooves properly. Verify that the bottom block is not twisted (no two lengths of wire rope should touch).

IT IS INTERESTING:  How much power does a tower crane used?

What is Crane checklist?

Checking for visible damages including wire ropes, crane hook, outriggers. … etc. Checking the machine condition such as control, brakes, warning signs and more. Checking and inspecting the area of operation.

What are the principal parts of an overhead traveling crane?

Category 2 and 3 Crane Components The principal parts of overhead traveling cranes are: bridge girders, end trucks, trolley with hoisting mechanism, and operator’s cab or pendant control. Critical Crane Components Careful repair and maintenance are essential to safe crane operations.

How often do overhead cranes need to be inspected?

OSHA requires that all active cranes must be inspected once a year at the minimum. However, depending on the cranes usage, additional inspections will be required. Crane inspections fall under two general categories based on the intervals between inspections.

Who can operate a crane?

Operators of most cranes above 2,000 lb. capacity when used in construction will need to be either certified by an accredited crane operator testing organization, such as the National Commission for the Certification of Crane Operators (NCCCO), or qualified through an audited employer program [§ 1926.1427(a)].

What is the problem of a crane?

If overhead crane is out of alignment and skewing then it can lead to significant stress and damage to whole crane system. While construction of the crane, forces applied can also cause stress in the crane and hence this type of stress can result in accidents, crane failure, productivity loss and replacement of loss.

How often do cranes need to be load tested?

4. Periodic Inspection. Like the Frequent Inspection, the frequency of the Periodic Inspection is based on the usage of the crane. For this inspection, cranes which are used for “normal service” and “heavy service” should be inspected yearly.

IT IS INTERESTING:  Why do cranes need to rotate?

How do you stop an overhead crane from swinging?

You should familiarize yourself with how to stop it. In some cases, you can do it by gradually pulling your throttle in the opposite direction of the way your crane is swinging. In others, moving your boom up and down repeatedly will steady the crane. The key is to counteract the motion of your crane to get it to stop.

What are the main parts of a crane?

The Various Functions of Mobile Crane Parts

  • The Driving Components. In any mobile crane, one of the common components will be the driving system used to make it mobile. …
  • The Operator’s Cabin. The operator’s cabin houses all of the crane’s controls. …
  • The Boom. …
  • Hoist and Hook. …
  • Hydraulic Pump. …
  • Outriggers and Counterweights.

6 февр. 2020 г.

What are the most common types of crane accidents?

OSHA’s analysis of crane accidents identified the major causes of crane accidents as:

  • boom or crane contact with energized power lines (nearly 45% of the cases)
  • under the hook lifting device.
  • overturned cranes.
  • dropped loads.
  • boom collapse.
  • crushing by the counter weight.
  • outrigger use, falls and rigging failures.

What does OSHA consider a crane?

A crane is a machine for lifting and lowering a load and moving it horizontally, with the hoisting mechanism an integral part of the machine. … Floor-operated crane means a crane which is pendant or nonconductive rope controlled by an operator on the floor or an independent platform.

Which motor is used in overhead crane?

While series DC motors consume more power than PMDC motors to produce their electromagnetic field, they’re powerful, efficient at high speeds and produce the most torque; hence, they are used for heavy duty winches. Shunt DC motors are used in constant speed applications, 18 such as reel drives.

IT IS INTERESTING:  Which type of motor is used in cranes?

What is the purpose of overhead crane?

To move extremely heavy or bulky loads through the overhead space in a facility, instead of through aisles or on the floor, an overhead crane (also called an industrial crane, crane, or overhead traveling crane is a machine that lifts, lowers and moves a load horizontally.

What are the major advantages of overhead Travelling Crane?

What are the Benefits of Overhead Cranes?

  • Increased Safety. Forklifts carry the risk of imprecise stacking, dropping goods as well as accidents (due to crashing). …
  • Improved Load Control. …
  • Avoid Floor Obstructions. …
  • Improved Ergonomics. …
  • Easy Lifting of Loads. …
  • Customizable.

29 июл. 2016 г.

Vira!